All cameras, NVRs and DVRs come with a 3-year back-to-base manufacturer warranty covering defects in materials and workmanship, in addition to your rights under Australian Consumer Law. Hard drives and accessories are covered as set out in our Warranty Policy.
Standard shipping is free on all orders over $300 AUD, Australia-wide. Orders under $300 ship at a flat rate of $25, calculated at checkout. Tracking is included on every order.
You have 30 days from the day you receive your order to request a change-of-mind return. Items must be unopened, factory-sealed and in resalable condition. A 15% restocking fee applies and return postage is at your cost. Faulty or incorrectly supplied items are different: we cover the return shipping and refund or replace at no charge. Read the full Return & Refund Policy.
Metro delivery usually takes 2–4 business days after dispatch, and regional areas may take longer. You'll receive a tracking number by email as soon as your order leaves the warehouse.
Alarm Modules & Expanders
Hikvision DS-PM1-O1H-WB Wall Switch
The Hikvision DS-PM1-O1H-WB is a wireless wall switch for AX PRO alarm systems, with a high-power relay that switches mains circuits directly. Linked to your alarm by 433MHz two-way wireless, it can turn lighting or appliances on and off on an alarm, a schedule or a manual command - no control cable back to the hub.
At a glance
- Single relay output, NO/NC, 100-240V AC up to 13A - switches mains loads directly
- 433MHz two-way wireless (2GFSK) to the AX PRO hub, up to 800m, AES-128 encrypted
- Scenario control: by alarm, by operation, by fault, by schedule or manual
- Mains powered (100-240V AC, 50/60Hz); wall mount or inside a standard 86 box
- Three status LEDs (register/signal, power, relay); licensed electrician required for mains wiring
Hikvision DS-PM2-S(AU) AX Hybrid Pro Series, Wired 3G/4G Communication Module
The Hikvision DS-PMA is a 3G/4G communication module for Hikvision AX Hybrid Pro hardwired alarm panels. It plugs into the panel and adds a cellular reporting path, so alarms and notifications can be sent over the mobile network - ideal where there is no phone line, or as a backup to a wired internet connection.
At a glance
- Adds 3G/4G cellular reporting to AX Hybrid Pro hardwired panels
- SIM card slot - a suitable SIM and mobile coverage are required
- Plug-in module design for a neat install inside the panel
- Use as a primary or backup reporting path
- Communication accessory only - panel and devices ordered separately
Hikvision AX PRO Series DS-PM1-O1L-WB Relay Module
The Hikvision DS-PM1-O1L-WB is a wireless relay output module for Hikvision AX PRO alarm systems. It lets the alarm switch a low-voltage circuit - by an alarm event, a schedule, a fault, or manually from the Hik-Connect app - so you can automate devices such as a gate, a light or an indicator without running a wired output back to the hub.
Key points
- One NO/NC relay output, 0-36 VDC, up to 5 A
- Triggered by alarm, manual app control, schedule or fault
- 433 MHz two-way wireless with AES-128 encryption, up to 800 m
- Flexible DC 7-24 V power input
- Three status LEDs for register/signal, power and relay state
- Compact wall-mount module, 38 x 25 x 18 mm
Bosch B426-M Ethernet IP Module for Solution 2000/3000/4000
The Bosch B426-M puts a Solution 2000, 3000 or 4000 alarm panel on the network: a four-wire bus module with an RJ-45 port that gives the panel two-way IP reporting to a monitoring centre, remote programming, and the internet path the RSC+ phone app runs over.
What you get
- 1 × B426-M Conettix Ethernet communication module PCB with the mounting screws and bracket for the enclosure's 3-hole pattern
You'll also need
- A compatible panel: the ICP-SOL3-P or ICP-SOL4-P board, or the panel inside a Solution 2000 or 3000 kit, at firmware V2.0 or higher for the cloud connection
- A Category 5 or better Ethernet lead from the module to the router, up to 100 m
- A keypad such as the IUI-SOL-ICON, or A-Link Plus software, to enable the module in panel programming
Digiflex MY369AU 4G GPRS/IP Interface Module Solution 6000
The Digiflex MY369AU gives a Bosch Solution 6000 a mobile data path for reporting and app control where a wired internet connection is unreliable or absent: a 4G GPRS/IP interface module with a dual carrier SIM and an RJ45 port, antenna included, for panels on firmware V2.51.04+.
What you get
- 1 × MY369AU 4G GPRS/IP interface module with its antenna
You’ll also need
- A Bosch Solution 6000 control panel on firmware V2.51.04 or later
- A MyAlarm subscription for the app and its notifications
Bosch CM910 Direct Link & Flash Programming USB Cable
The Bosch CM910 is the installer's USB cable for Bosch Solution panels: a combined direct link and flash programmer that connects a Windows PC to the panel's 10 way serial header for on-site Solution Link programming sessions or firmware updates, with a select switch to choose between the two.
What you get
- 1 × CM910B direct link and flash programmer with a 10 way flying lead to the panel serial port header and a 5 metre USB cable
You'll also need
- A supported panel: Solution 16i, Solution 16Plus, Solution 64, Solution 144 or Solution 6000, sold here as the CC610P board
- A Windows PC with Solution Link software and the USB driver from the Solution Link RAS DVD or alarmsoftware.com.au
- The correct firmware file for the panel when flashing, and a Solution Link backup taken first
- For a panel with a lost installer code, the CM255B default key rather than this cable
Bosch CM796B Wiegand to RS485 LAN Interface Module
The Bosch CM796B is the interface module for a Solution 6000 or Solution 144 site that wants to use a third-party proximity reader: it takes a 26bit to 40bit Wiegand reader such as the PR100B and puts it on the panel's RS485 LAN as a reader address, with LED and buzzer control for the reader.
What you get
- 1 × CM796B module PCB with mounting spacer pack, installer reference guide and 2 shunts
You'll also need
- A Solution 6000 panel on version 2.12 or later, such as the CC610P panel PCB, or a Solution 144 on version 2.08 or later
- A PR100B or other suitable 26bit to 40bit Wiegand reader with matching cards or tokens
- A power supply for the reader, such as the CM720B, wired to the module's separately fused reader power terminals
Bosch CM705PB Universal Zone & Output Expander Solution 6000
The Bosch CM705PB is the universal expander PCB for the Solution 6000: one LAN module that adds up to 16 zone inputs, 4 monitored 500mA outputs and power terminals with a battery charger.
What you get
- Bosch CM705PB universal expander module — PCB only
You'll also need
- A compatible Solution 6000 control panel
- A 16-18V AC 50-60Hz – 24VA External Power Adaptor or internal transformer, a 12V DC, 7.2AH battery for the module's own supply and a suitable enclosure
- Detectors for the new zones and any devices required for the programmable outputs
Before you buy
What customers ask most before ordering from this range — and how we deliver.
Which kit is right for me?
Start with three questions: how many areas do you need to cover, do you want colour night vision, and do you want AI alerts that ignore cars and animals? For most homes, a 4-camera 8MP ColorVu or Full-Colour kit is the sweet spot. Not sure? Use our CCTV Advisor — answer a few questions and it recommends a kit — or email us and we'll spec it with you.
Is your Hikvision, Dahua, HiLook and TP-Link VIGI stock genuine Australian stock?
Yes, 100%. Every Hikvision, Dahua, HiLook and TP-Link VIGI product we sell is a genuine Australian-market model sourced through Australian supply chains — never grey imports. That means factory-sealed units, Australian-region firmware that works with the official apps out of the box, and a full 3-year local warranty.
How long does delivery take?
Metro delivery usually takes 2–4 business days after dispatch, and regional areas may take longer. You'll receive a tracking number by email as soon as your order leaves the warehouse.
How much is shipping?
Standard shipping is free on all orders over $300 AUD, Australia-wide. Orders under $300 ship at a flat rate of $25, calculated at checkout. Tracking is included on every order.
What warranty do you offer?
All cameras, NVRs and DVRs come with a 3-year back-to-base manufacturer warranty covering defects in materials and workmanship, in addition to your rights under Australian Consumer Law. Hard drives and accessories are covered as set out in our Warranty Policy.
What is your return policy?
You have 30 days from the day you receive your order to request a change-of-mind return. Items must be unopened, factory-sealed and in resalable condition. A 15% restocking fee applies and return postage is at your cost. Faulty or incorrectly supplied items are different: we cover the return shipping and refund or replace at no charge. Read the full Return & Refund Policy.
Do you offer installation?
We can connect you with licensed installers in Sydney and Melbourne. Installation typically starts from around $200 per camera depending on cable runs and site conditions. Email sales@smarket.com.au with your address and camera count for a quote.
Alarms by Brand
Compare alarm systems across the range
Security Cameras
Add cameras alongside your alarm system
