All cameras, NVRs and DVRs come with a 3-year back-to-base manufacturer warranty covering defects in materials and workmanship, in addition to your rights under Australian Consumer Law. Hard drives and accessories are covered as set out in our Warranty Policy.
Standard shipping is free on all orders over $300 AUD, Australia-wide. Orders under $300 ship at a flat rate of $25, calculated at checkout. Tracking is included on every order.
You have 30 days from the day you receive your order to request a change-of-mind return. Items must be unopened, factory-sealed and in resalable condition. A 15% restocking fee applies and return postage is at your cost. Faulty or incorrectly supplied items are different: we cover the return shipping and refund or replace at no charge. Read the full Return & Refund Policy.
Metro delivery usually takes 2–4 business days after dispatch, and regional areas may take longer. You'll receive a tracking number by email as soon as your order leaves the warehouse.
Alarm Modules & Expanders
Bosch CM255B Panel Default Unlock Key for Solution 6000
The Bosch CM255B is the way into a Solution panel whose installer PIN nobody knows: a single-use plug-in key that resets the installer PIN and RAS security PIN on a Solution 6000, so the panel is taken over on site instead of being unwired and returned for defaulting.
What you get
- 1 × CM255B factory default module, blue, with red and green status indicators, for one use only
You'll also need
- Access to the panel board and its 10-pin connector marked Serial Port or Direct Link Port, such as on the CC610P
- A new key for every panel defaulted, because a used key cannot be used again
Dahua DHI-ARM7012-W2 Wireless WallSwitch
The Dahua DHI-ARM7012-W2 is a wireless WallSwitch for the Dahua AirShield alarm system. It lets you switch a mains appliance on or off remotely from the DMSS app, run it on a schedule or trigger it from an alarm event, and it monitors how much power that appliance is using. It handles loads up to 13 A at 100-240 VAC and links to your AirShield hub over an encrypted two-way wireless connection. An AirShield hub is required and sold separately.
Key points
- Remote on/off control of a 100-240 VAC appliance, up to 13 A
- Single relay output, switchable as normally-open or normally-closed
- Live energy monitoring: voltage, current and consumption in the DMSS app
- Overheat and overload protection built in
- Encrypted two-way wireless (AES128, frequency hopping) with jamming detection
- Range up to 1,200 m in open space to the hub
- Mains powered, indoor wall mount; requires a Dahua AirShield hub
Dahua DHI-ARM320-W2 Wireless Input Expander
The Dahua DHI-ARM320-W2 is a wireless input expander for the Dahua AirShield alarm system. It lets you connect an existing third-party wired detector — a PIR, reed, smoke or panic device — and bring it into your wireless alarm, so when that detector triggers, the expander reports it to the hub over the air. It can even supply low-voltage power to the connected detector, and it runs for years on its own batteries. An AirShield hub is required and sold separately.
Key points
- Connects a third-party wired detector to the Dahua AirShield wireless system
- One alarm input plus a second input for the detector's tamper port
- Six alarm types selectable in the app: intrusion, medical, fire, emergency, gas, tamper
- Auxiliary 3.3 V output (up to 10 mA) to power the connected detector
- Encrypted two-way wireless (AES128, frequency hopping), up to 1,300 m
- Triaxial accelerometer for a device-moved alarm; tamper protection
- 4 x AA batteries for around 3 years of life; indoor; requires a Dahua AirShield hub
Dahua DHI-ARM310-W2 Wireless Input Expander
The Dahua DHI-ARM310-W2 is a wireless input expander for the Dahua AirShield alarm system. It takes a single wired detector — one that only comes in a hard-wired form, or an existing wired sensor you want to keep — and reports it to the hub wirelessly, so you can fold a wired device into an otherwise wireless system without running cable back to a panel. It links to the hub over an encrypted two-way RF connection and runs on a battery. An AirShield hub is required and sold separately.
Key points
- Converts one wired (NO/NC) detector input into an AirShield wireless zone
- Reports six alarm types: intrusion, medical, fire, emergency, gas and tamper
- Encrypted two-way RF link with frequency hopping; signal-strength check
- Ambient temperature monitoring and low-battery alarm
- 4 x AA batteries for around 3 years (NO input) or 2 years (NC/pulse)
- Indoor, bracket mount; requires a Dahua AirShield hub
The Dahua DHI-ARM7011-W2 is a wireless relay for the Dahua AirShield alarm system. It gives the system a switched, isolated dry contact (0-36 VDC, up to 5 A) that you can trigger from the app, on a schedule, in a scene, or automatically when an alarm event happens — handy for switching a light, a gate or garage trigger, or an extra warning device. It links to the hub over an encrypted two-way radio link and has overheat and overvoltage protection built in. An AirShield hub is required and sold separately.
Key points
- One isolated dry-contact relay output, 0-36 VDC, up to 5 A
- Trigger from the app, a schedule, a scene or an alarm event
- Encrypted two-way radio with AES128 and frequency hopping; range up to 800 m
- Overheat and overvoltage protection; one tamper input
- Powered from 7-24 V DC; compact wall mount
- Requires a Dahua AirShield hub
Hikvision DS-PM1-I16O2-WB AX PRO Wireless 16-Input & 2-Output Expander
The Hikvision DS-PM1-I16O2-WB is an AX PRO wireless multi-I/O expander that lets you keep existing wired detectors when you move to a Hikvision AX PRO wireless alarm. It connects up to sixteen hardwired inputs and two outputs and reports them back to the wireless hub over Tri-X radio - so legacy cabling and sensors stay in use instead of being replaced.
At a glance
- Integrates up to 16 wired alarm inputs and 2 outputs into an AX PRO wireless system
- Tri-X two-way 433MHz radio to the hub, up to 800m open-air, AES-128 secured
- Each zone independently set to NO/NC, EOL or DEOL for professional wired sensors
- Mains powered 100-240 VAC, takes a 12V 7Ah backup battery for up to 36 hours
- For AX PRO wireless hubs - not for the DS-PHA64 hardwired panel
Hikvision DS-PM2-S(AU) 3G/4G Communication Module(AU)
The Hikvision DS-PM2-S(AU) is a 3G/4G communication module that adds cellular reporting to a Hikvision AX Hybrid Pro alarm panel. With a SIM fitted, the panel can send alarms and notifications over the mobile network - useful where there is no phone line, or as a resilient backup to a wired internet path.
At a glance
- Adds 3G/4G cellular alarm reporting to AX Hybrid Pro hardwired panels
- AU variant: LTE-FDD B1/B3/B5/B7/B8/B28/B66, LTE-TDD B40, WCDMA and GSM
- SIM card slot - a suitable SIM and mobile coverage are required
- Plug-in module design for neat installation inside the panel
- Use as a primary or backup reporting path, -10 to +40 degrees C
Hikvision DS-PM1-O4H-H AX Hybrid Pro 4-Way Output Module to suit Hardwired Alarm Controller
The Hikvision DS-PM1-O4H-H is a wired 4-way power output module for AX Hybrid Pro hardwired alarm controllers. It gives the panel four high-current relays that can switch mains-powered devices - sirens, strobes, lighting circuits, gates and shutters - on command over the Speed-X bus, turning an alarm event into real-world action.
At a glance
- Four onboard power relays, each rated to switch up to 16A
- Connects to a 100-240 VAC source and opens/closes circuits on command
- Controlled by the AX Hybrid Pro panel over the Speed-X bus
- Cascade support: 1 uplink and 1 downlink Speed-X port for more expanders
- Front and rear tamper, plastic enclosure, mains wiring by a licensed electrician
Before you buy
What customers ask most before ordering from this range — and how we deliver.
Which kit is right for me?
Start with three questions: how many areas do you need to cover, do you want colour night vision, and do you want AI alerts that ignore cars and animals? For most homes, a 4-camera 8MP ColorVu or Full-Colour kit is the sweet spot. Not sure? Use our CCTV Advisor — answer a few questions and it recommends a kit — or email us and we'll spec it with you.
Is your Hikvision, Dahua, HiLook and TP-Link VIGI stock genuine Australian stock?
Yes, 100%. Every Hikvision, Dahua, HiLook and TP-Link VIGI product we sell is a genuine Australian-market model sourced through Australian supply chains — never grey imports. That means factory-sealed units, Australian-region firmware that works with the official apps out of the box, and a full 3-year local warranty.
How long does delivery take?
Metro delivery usually takes 2–4 business days after dispatch, and regional areas may take longer. You'll receive a tracking number by email as soon as your order leaves the warehouse.
How much is shipping?
Standard shipping is free on all orders over $300 AUD, Australia-wide. Orders under $300 ship at a flat rate of $25, calculated at checkout. Tracking is included on every order.
What warranty do you offer?
All cameras, NVRs and DVRs come with a 3-year back-to-base manufacturer warranty covering defects in materials and workmanship, in addition to your rights under Australian Consumer Law. Hard drives and accessories are covered as set out in our Warranty Policy.
What is your return policy?
You have 30 days from the day you receive your order to request a change-of-mind return. Items must be unopened, factory-sealed and in resalable condition. A 15% restocking fee applies and return postage is at your cost. Faulty or incorrectly supplied items are different: we cover the return shipping and refund or replace at no charge. Read the full Return & Refund Policy.
Do you offer installation?
We can connect you with licensed installers in Sydney and Melbourne. Installation typically starts from around $200 per camera depending on cable runs and site conditions. Email sales@smarket.com.au with your address and camera count for a quote.
Alarms by Brand
Compare alarm systems across the range
Security Cameras
Add cameras alongside your alarm system
