All cameras, NVRs and DVRs come with a 3-year back-to-base manufacturer warranty covering defects in materials and workmanship, in addition to your rights under Australian Consumer Law. Hard drives and accessories are covered as set out in our Warranty Policy.
Standard shipping is free on all orders over $300 AUD, Australia-wide. Orders under $300 ship at a flat rate of $25, calculated at checkout. Tracking is included on every order.
You have 30 days from the day you receive your order to request a change-of-mind return. Items must be unopened, factory-sealed and in resalable condition. A 15% restocking fee applies and return postage is at your cost. Faulty or incorrectly supplied items are different: we cover the return shipping and refund or replace at no charge. Read the full Return & Refund Policy.
Order before 2pm (Sydney time) on a business day and in-stock items are dispatched the same day. Most orders arrive within 1–4 business days Australia-wide; remote and regional areas can take a little longer. You'll receive a tracking number by email as soon as your order leaves the warehouse.
Alarm Modules & Expanders
Hikvision DS-PM2-S(AU) AX Hybrid Pro Series, Wired 3G/4G Communication Module
The Hikvision DS-PMA is a 3G/4G communication module for Hikvision AX Hybrid Pro hardwired alarm panels. It plugs into the panel and adds a cellular reporting path, so alarms and notifications can be sent over the mobile network - ideal where there is no phone line, or as a backup to a wired internet connection.
At a glance
- Adds 3G/4G cellular reporting to AX Hybrid Pro hardwired panels
- SIM card slot - a suitable SIM and mobile coverage are required
- Plug-in module design for a neat install inside the panel
- Use as a primary or backup reporting path
- Communication accessory only - panel and devices ordered separately
Hikvision DS-PM1-I8O2-H Ax Hybrid Pro RS485 wired Input Expander
The Hikvision DS-PM1-I8O2-H is a Speed-X wired input expander for the AX Hybrid Pro alarm panel. It adds eight on-board wired zones and two collector outputs to a hardwired system, so you can connect more detectors, contacts and output devices than the panel alone supports.
At a glance
- Adds 8 wired zones + 2 outputs to an AX Hybrid Pro (DS-PHA64) panel
- Connects over the Speed-X bus, up to 900m of cable, and cascades to further expanders
- 3EOL wiring (1k alarm / 1k tamper / 2.2k fault) with zone, tamper, mask, fault and short detection
- 11-24VDC input; output 9-12VDC up to 500mA to power wired detectors directly
- Front and rear tamper protection; power and fault LED indicators
- Wired expansion module - not for the wireless AX PRO (PWA96) hub
Hikvision AX PRO Series DS-PM1-O1L-WB Relay Module
The Hikvision DS-PM1-O1L-WB is a wireless relay output module for Hikvision AX PRO alarm systems. It lets the alarm switch a low-voltage circuit - by an alarm event, a schedule, a fault, or manually from the Hik-Connect app - so you can automate devices such as a gate, a light or an indicator without running a wired output back to the hub.
Key points
- One NO/NC relay output, 0-36 VDC, up to 5 A
- Triggered by alarm, manual app control, schedule or fault
- 433 MHz two-way wireless with AES-128 encryption, up to 800 m
- Flexible DC 7-24 V power input
- Three status LEDs for register/signal, power and relay state
- Compact wall-mount module, 38 x 25 x 18 mm
Bosch CM751B Conettix IP Ethernet Module for Solution 6000
The Bosch CM751B is the plug-on Ethernet module for a Solution 6000 owner who wants the panel on the network instead of a phone line: monitored reporting in Conettix or CSV-IP format with 128 bit AES encryption, remote programming over IP, and the wired path for the MyAlarm app.
What you get
- 1 × CM751B Conettix IP Ethernet module with three PCB standoffs and the HW750 riser kit
You'll also need
- A Solution 6000 control panel, sold here as the CC610P panel PCB or in the CC610GWP panel and keypad kit
- A network cable from the panel cabinet to the router or switch
- A MyAlarm subscription if app control is wanted; it is a paid service that Bosch does not run
Bosch CM710B 4 x Form C Relay Output Expansion Module
The Bosch CM710B is the module for a Solution 6000 or Solution 16i owner who has run out of outputs: it adds four Form C relay outputs, rated 24VDC at 2A MAX, on a PCB that sits in the panel cabinet or in its own enclosure at the far end of the LAN.
What you get
- 1 × CM710B output expansion module PCB with four Form C relay outputs, status LED, separate tamper input and a service code pad connection
You'll also need
Bosch CM704B 8/16 Zone Expansion Module for Solution 6000
The Bosch CM704B is the zone expansion module for a Solution 6000 system that has run out of detector inputs: a PCB on the panel's 4 wire LAN that adds 8 physical zone inputs, giving 8 or 16 zones depending on the end-of-line configuration.
What you get
- 1 × CM704B 8/16 zone expansion module PCB with status and zone power LEDs, a service code pad connection and a separate tamper input
You'll also need
- A Solution 6000 panel: the CC610P board, the CC610GWP kit or the CC610GWF-2 kit
- One free module space in the panel cabinet or a separate enclosure, plus 4 wire LAN cable to reach it
- Detectors for the new zones, such as these sold here: the ISC-BPR2-WP12 PIR or the DS1101i glass-break detector
Before you buy
What customers ask most before ordering from this range — and how we deliver.
Which kit is right for me?
Start with three questions: how many areas do you need to cover, do you want colour night vision, and do you want AI alerts that ignore cars and animals? For most homes, a 4-camera 8MP ColorVu or Full-Colour kit is the sweet spot. Not sure? Use our CCTV Advisor — answer a few questions and it recommends a kit — or email us and we'll spec it with you.
Is your Hikvision, Dahua, HiLook and TP-Link VIGI stock genuine Australian stock?
Yes, 100%. Every Hikvision, Dahua, HiLook and TP-Link VIGI product we sell is a genuine Australian-market model sourced through Australian supply chains — never grey imports. That means factory-sealed units, Australian-region firmware that works with the official apps out of the box, and a full 3-year local warranty.
How long does delivery take?
Order before 2pm (Sydney time) on a business day and in-stock items are dispatched the same day. Most orders arrive within 1–4 business days Australia-wide; remote and regional areas can take a little longer. You'll receive a tracking number by email as soon as your order leaves the warehouse.
How much is shipping?
Standard shipping is free on all orders over $300 AUD, Australia-wide. Orders under $300 ship at a flat rate of $25, calculated at checkout. Tracking is included on every order.
What warranty do you offer?
All cameras, NVRs and DVRs come with a 3-year back-to-base manufacturer warranty covering defects in materials and workmanship, in addition to your rights under Australian Consumer Law. Hard drives and accessories are covered as set out in our Warranty Policy.
What is your return policy?
You have 30 days from the day you receive your order to request a change-of-mind return. Items must be unopened, factory-sealed and in resalable condition. A 15% restocking fee applies and return postage is at your cost. Faulty or incorrectly supplied items are different: we cover the return shipping and refund or replace at no charge. Read the full Return & Refund Policy.
Do you offer installation?
We can connect you with licensed installers in Sydney and Melbourne. Installation typically starts from around $200 per camera depending on cable runs and site conditions. Email sales@smarket.com.au with your address and camera count for a quote.
Alarms by Brand
Compare alarm systems across the range
Security Cameras
Add cameras alongside your alarm system
