All cameras, NVRs and DVRs come with a 3-year back-to-base manufacturer warranty covering defects in materials and workmanship, in addition to your rights under Australian Consumer Law. Hard drives and accessories are covered as set out in our Warranty Policy.
Standard shipping is free on all orders over $300 AUD, Australia-wide. Orders under $300 ship at a flat rate of $25, calculated at checkout. Tracking is included on every order.
You have 30 days from the day you receive your order to request a change-of-mind return. Items must be unopened, factory-sealed and in resalable condition. A 15% restocking fee applies and return postage is at your cost. Faulty or incorrectly supplied items are different: we cover the return shipping and refund or replace at no charge. Read the full Return & Refund Policy.
Metro delivery usually takes 2–4 business days after dispatch, and regional areas may take longer. You'll receive a tracking number by email as soon as your order leaves the warehouse.
Hikvision Alarm
X2 Reed, Mini Heavy Duty Metal Reed Switch, Surface Mount, 30mm Gap
The X2-REED-301 is a compact, heavy-duty metal reed switch for monitoring the open or closed state of doors and windows in demanding spots. It is a wired, normally-closed switch with a 480 mm armoured cable and a 30 mm operating gap, which makes it well suited to roller doors, fire doors and roof hatches where a small but tough sensor is needed. It wires into any hardwired alarm zone.
Key points
- Mini heavy-duty metal reed switch, surface mount
- Wired, normally-closed (NC) contact for any hardwired alarm zone
- 30 mm operating gap; 480 mm armoured cable
- Rated 100 V DC/AC, 0.5 A, 10 W
- Silver zinc alloy body; -20°C to 80°C; rated for 100,000+ operations
- CCC / CE / FCC / RoHS
Tactical Power Supply, 14.3V DC, 2.5A, Plug Pack, Required for Hikvision Hybrid Alarm
The Tactical TP-TP14.3-2.5APP is the plug-pack power supply that runs a Hikvision AX Hybrid Pro alarm panel. It delivers a regulated 14.3V DC at 2.5A from a standard wall socket, providing the working power the DS-PHA64 control panel needs - the correct, specified replacement or spare adapter for these wired Hikvision alarm systems.
At a glance
- 14.3V DC, 2.5A plug-pack power supply (up to 35.75W)
- Required to power the Hikvision AX Hybrid Pro DS-PHA64 panel
- Wide 100-240V AC input, wall-mounted compact design
- Correct specified spare or replacement adapter
- Power supply only - panel and backup battery are separate
Hikvision DS-PWA96-Kit-WB-COMPLETE AX PRO Complete Alarm Security Kit
This Hikvision AX PRO complete alarm kit is a wireless intrusion starter system built on the DS-PWA96-M-WB hub, supplied with a keypad, two PIR motion detectors, a door contact and an outdoor siren, all managed from the Hik-Connect app.
What's in the kit
- 1 x DS-PWA96-M-WB AX PRO wireless alarm hub (96 zones)
- 1 x DS-PK1-E-WB wireless PIN keypad
- 2 x DS-PDP15P-EG2-WB wireless PIR detectors (15 m, 30 kg pet immunity)
- 1 x DS-PDMC-EG2-WB wireless magnetic door contact
- 1 x DS-PS1-E-WB wireless outdoor sounder
- Wi-Fi, wired LAN and 3G/4G SIM reporting paths
- Tri-X two-way wireless with AES-128 encryption
Hikvision DS-PT1-WB Ax Pro Wireless Mifare Tag Reader
The Hikvision DS-PT1-WB is a wireless Mifare tag reader for Hikvision AX PRO alarm systems, operating on the 433MHz band. Fit it beside a door and users arm or disarm the alarm with a quick swipe of a Mifare tag - no PIN to remember - making everyday control faster at busy entry points.
At a glance
- Wireless Mifare tag reader for arming and disarming an AX PRO alarm
- 433MHz two-way wireless - must match your AX PRO hub's RF band
- AES-128 encryption and clear multi-colour LED feedback
- Up to 900m open-air range; front and rear tamper protection
- 3 x AA batteries, up to 2 years standby, slim 75 x 124 x 21 mm
Hikvision DS-PR1-WB AX Pro Wireless Repeater
The Hikvision DS-PR1-WB is a wireless repeater for Hikvision AX PRO alarm systems. It relays the 433 MHz two-way signal between the control panel and distant detectors, so devices in a far corner, a detached building or behind dense walls stay reliably connected. It is mains powered with a built-in battery for backup, and supports PIRCAM image-verification detectors.
Key points
- Extends AX PRO 433 MHz two-way wireless range, up to 800 m open area
- Supports PIRCAM image-verification detectors
- 433 MHz two-way wireless with AES-128 encryption; auto-pairing
- Mains powered (100-240 VAC) with built-in Li battery
- Up to ~35 hours' battery backup at normal temperature
- Three status LEDs; front and rear tamper; wall mount
Hikvision DS-PM1-O4H-H AX Hybrid Pro 4-Way Output Module to suit Hardwired Alarm Controller
The Hikvision DS-PM1-O4H-H is a wired 4-way power output module for AX Hybrid Pro hardwired alarm controllers. It gives the panel four high-current relays that can switch mains-powered devices - sirens, strobes, lighting circuits, gates and shutters - on command over the Speed-X bus, turning an alarm event into real-world action.
At a glance
- Four onboard power relays, each rated to switch up to 16A
- Connects to a 100-240 VAC source and opens/closes circuits on command
- Controlled by the AX Hybrid Pro panel over the Speed-X bus
- Cascade support: 1 uplink and 1 downlink Speed-X port for more expanders
- Front and rear tamper, plastic enclosure, mains wiring by a licensed electrician
Hikvision DS-PM1-I8O2-H Ax Hybrid Pro RS485 wired Input Expander
The Hikvision DS-PM1-I8O2-H is a Speed-X wired input expander for the AX Hybrid Pro alarm panel. It adds eight on-board wired zones and two collector outputs to a hardwired system, so you can connect more detectors, contacts and output devices than the panel alone supports.
At a glance
- Adds 8 wired zones + 2 outputs to an AX Hybrid Pro (DS-PHA64) panel
- Connects over the Speed-X bus, up to 900m of cable, and cascades to further expanders
- 3EOL wiring (1k alarm / 1k tamper / 2.2k fault) with zone, tamper, mask, fault and short detection
- 11-24VDC input; output 9-12VDC up to 500mA to power wired detectors directly
- Front and rear tamper protection; power and fault LED indicators
- Wired expansion module - not for the wireless AX PRO (PWA96) hub
Hikvision DS-PM1-I16O2-WB AX PRO Wireless 16-Input & 2-Output Expander
The Hikvision DS-PM1-I16O2-WB is an AX PRO wireless multi-I/O expander that lets you keep existing wired detectors when you move to a Hikvision AX PRO wireless alarm. It connects up to sixteen hardwired inputs and two outputs and reports them back to the wireless hub over Tri-X radio - so legacy cabling and sensors stay in use instead of being replaced.
At a glance
- Integrates up to 16 wired alarm inputs and 2 outputs into an AX PRO wireless system
- Tri-X two-way 433MHz radio to the hub, up to 800m open-air, AES-128 secured
- Each zone independently set to NO/NC, EOL or DEOL for professional wired sensors
- Mains powered 100-240 VAC, takes a 12V 7Ah backup battery for up to 36 hours
- For AX PRO wireless hubs - not for the DS-PHA64 hardwired panel
Before you buy
What customers ask most before ordering from this range — and how we deliver.
Which kit is right for me?
Start with three questions: how many areas do you need to cover, do you want colour night vision, and do you want AI alerts that ignore cars and animals? For most homes, a 4-camera 8MP ColorVu or Full-Colour kit is the sweet spot. Not sure? Use our CCTV Advisor — answer a few questions and it recommends a kit — or email us and we'll spec it with you.
Is your Hikvision, Dahua, HiLook and TP-Link VIGI stock genuine Australian stock?
Yes, 100%. Every Hikvision, Dahua, HiLook and TP-Link VIGI product we sell is a genuine Australian-market model sourced through Australian supply chains — never grey imports. That means factory-sealed units, Australian-region firmware that works with the official apps out of the box, and a full 3-year local warranty.
How long does delivery take?
Metro delivery usually takes 2–4 business days after dispatch, and regional areas may take longer. You'll receive a tracking number by email as soon as your order leaves the warehouse.
How much is shipping?
Standard shipping is free on all orders over $300 AUD, Australia-wide. Orders under $300 ship at a flat rate of $25, calculated at checkout. Tracking is included on every order.
What warranty do you offer?
All cameras, NVRs and DVRs come with a 3-year back-to-base manufacturer warranty covering defects in materials and workmanship, in addition to your rights under Australian Consumer Law. Hard drives and accessories are covered as set out in our Warranty Policy.
What is your return policy?
You have 30 days from the day you receive your order to request a change-of-mind return. Items must be unopened, factory-sealed and in resalable condition. A 15% restocking fee applies and return postage is at your cost. Faulty or incorrectly supplied items are different: we cover the return shipping and refund or replace at no charge. Read the full Return & Refund Policy.
Do you offer installation?
We can connect you with licensed installers in Sydney and Melbourne. Installation typically starts from around $200 per camera depending on cable runs and site conditions. Email sales@smarket.com.au with your address and camera count for a quote.
Security Cameras
Add cameras alongside your alarm system
