Hikvision Alarm

The Hikvision DS-PT1-WB is a wireless Mifare tag reader for Hikvision AX PRO alarm systems, operating on the 433MHz band. Fit it beside a door and users arm or disarm the alarm with a quick swipe of a Mifare tag - no PIN to remember - making everyday control faster at busy entry points.

At a glance
- Wireless Mifare tag reader for arming and disarming an AX PRO alarm
- 433MHz two-way wireless - must match your AX PRO hub's RF band
- AES-128 encryption and clear multi-colour LED feedback
- Up to 900m open-air range; front and rear tamper protection
- 3 x AA batteries, up to 2 years standby, slim 75 x 124 x 21 mm

The Hikvision DS-PT-M1 is a compact 13.56 MHz Mifare contactless tag for Hikvision AX PRO wireless alarm systems. Tap it on the control panel's built-in tag reader or an AX PRO keypad to arm or disarm without entering a code — ideal for family members or staff who do not need full app access.

Key points
- 13.56 MHz Mifare contactless tag for Hikvision AX PRO systems
- Tap to arm or disarm at the panel's tag reader or an AX PRO keypad
- 1024 × 8 bit EEPROM (16 sectors), approx. 10-year data retention
- Durable PVC / ABS body, 41 × 32 × 3.5 mm
- Up to 48 tags per AX PRO panel; available in white or black

The Hikvision DS-PR1-WB is a wireless repeater for Hikvision AX PRO alarm systems. It relays the 433 MHz two-way signal between the control panel and distant detectors, so devices in a far corner, a detached building or behind dense walls stay reliably connected. It is mains powered with a built-in battery for backup, and supports PIRCAM image-verification detectors.

Key points
- Extends AX PRO 433 MHz two-way wireless range, up to 800 m open area
- Supports PIRCAM image-verification detectors
- 433 MHz two-way wireless with AES-128 encryption; auto-pairing
- Mains powered (100-240 VAC) with built-in Li battery
- Up to ~35 hours' battery backup at normal temperature
- Three status LEDs; front and rear tamper; wall mount

The Hikvision DS-PMA is a 3G/4G communication module for Hikvision AX Hybrid Pro hardwired alarm panels. It plugs into the panel and adds a cellular reporting path, so alarms and notifications can be sent over the mobile network - ideal where there is no phone line, or as a backup to a wired internet connection.

At a glance
- Adds 3G/4G cellular reporting to AX Hybrid Pro hardwired panels
- SIM card slot - a suitable SIM and mobile coverage are required
- Plug-in module design for a neat install inside the panel
- Use as a primary or backup reporting path
- Communication accessory only - panel and devices ordered separately

The Hikvision DS-PM1-O4H-H is a wired 4-way power output module for AX Hybrid Pro hardwired alarm controllers. It gives the panel four high-current relays that can switch mains-powered devices - sirens, strobes, lighting circuits, gates and shutters - on command over the Speed-X bus, turning an alarm event into real-world action.

At a glance
- Four onboard power relays, each rated to switch up to 16A
- Connects to a 100-240 VAC source and opens/closes circuits on command
- Controlled by the AX Hybrid Pro panel over the Speed-X bus
- Cascade support: 1 uplink and 1 downlink Speed-X port for more expanders
- Front and rear tamper, plastic enclosure, mains wiring by a licensed electrician

The Hikvision DS-PM1-I8O2-H is a Speed-X wired input expander for the AX Hybrid Pro alarm panel. It adds eight on-board wired zones and two collector outputs to a hardwired system, so you can connect more detectors, contacts and output devices than the panel alone supports.

At a glance
- Adds 8 wired zones + 2 outputs to an AX Hybrid Pro (DS-PHA64) panel
- Connects over the Speed-X bus, up to 900m of cable, and cascades to further expanders
- 3EOL wiring (1k alarm / 1k tamper / 2.2k fault) with zone, tamper, mask, fault and short detection
- 11-24VDC input; output 9-12VDC up to 500mA to power wired detectors directly
- Front and rear tamper protection; power and fault LED indicators
- Wired expansion module - not for the wireless AX PRO (PWA96) hub

The Hikvision DS-PM1-I16O2-WB is an AX PRO wireless multi-I/O expander that lets you keep existing wired detectors when you move to a Hikvision AX PRO wireless alarm. It connects up to sixteen hardwired inputs and two outputs and reports them back to the wireless hub over Tri-X radio - so legacy cabling and sensors stay in use instead of being replaced.

At a glance
- Integrates up to 16 wired alarm inputs and 2 outputs into an AX PRO wireless system
- Tri-X two-way 433MHz radio to the hub, up to 800m open-air, AES-128 secured
- Each zone independently set to NO/NC, EOL or DEOL for professional wired sensors
- Mains powered 100-240 VAC, takes a 12V 7Ah backup battery for up to 36 hours
- For AX PRO wireless hubs - not for the DS-PHA64 hardwired panel

The Hikvision DS-PM1-I1-WB is a wireless input transmitter for AX PRO alarm systems. It bridges one existing wired detector, contact or alarm device into the AX PRO wireless system, so you can reuse proven wired hardware on a modern wireless panel without running new cable back to the hub.

At a glance
- Converts one wired alarm input (PIR, reed, vibration, contact) into a wireless AX PRO zone
- One alarm input, one tamper input, one programmable PGM output, plus a 3.3V output for low-current sensors
- Tri-X two-way wireless on 433MHz (2GFSK), up to 1300m open-air, AES-128
- Three CR123 batteries, up to 5 years; built-in tamper
- Compact module fits inside a wireless-ready detector or beside the wired device