All cameras, NVRs and DVRs come with a 3-year back-to-base manufacturer warranty covering defects in materials and workmanship, in addition to your rights under Australian Consumer Law. Hard drives and accessories are covered as set out in our Warranty Policy.
Standard shipping is free on all orders over $300 AUD, Australia-wide. Orders under $300 ship at a flat rate of $25, calculated at checkout. Tracking is included on every order.
You have 30 days from the day you receive your order to request a change-of-mind return. Items must be unopened, factory-sealed and in resalable condition. A 15% restocking fee applies and return postage is at your cost. Faulty or incorrectly supplied items are different: we cover the return shipping and refund or replace at no charge. Read the full Return & Refund Policy.
Metro delivery usually takes 2–4 business days after dispatch, and regional areas may take longer. You'll receive a tracking number by email as soon as your order leaves the warehouse.
Products
Hikvision DS-PM1-I8O2-H Ax Hybrid Pro RS485 wired Input Expander
The Hikvision DS-PM1-I8O2-H is a Speed-X wired input expander for the AX Hybrid Pro alarm panel. It adds eight on-board wired zones and two collector outputs to a hardwired system, so you can connect more detectors, contacts and output devices than the panel alone supports.
At a glance
- Adds 8 wired zones + 2 outputs to an AX Hybrid Pro (DS-PHA64) panel
- Connects over the Speed-X bus, up to 900m of cable, and cascades to further expanders
- 3EOL wiring (1k alarm / 1k tamper / 2.2k fault) with zone, tamper, mask, fault and short detection
- 11-24VDC input; output 9-12VDC up to 500mA to power wired detectors directly
- Front and rear tamper protection; power and fault LED indicators
- Wired expansion module - not for the wireless AX PRO (PWA96) hub
Hikvision DS-PM1-O1H-WB Wall Switch
The Hikvision DS-PM1-O1H-WB is a wireless wall switch for AX PRO alarm systems, with a high-power relay that switches mains circuits directly. Linked to your alarm by 433MHz two-way wireless, it can turn lighting or appliances on and off on an alarm, a schedule or a manual command - no control cable back to the hub.
At a glance
- Single relay output, NO/NC, 100-240V AC up to 13A - switches mains loads directly
- 433MHz two-way wireless (2GFSK) to the AX PRO hub, up to 800m, AES-128 encrypted
- Scenario control: by alarm, by operation, by fault, by schedule or manual
- Mains powered (100-240V AC, 50/60Hz); wall mount or inside a standard 86 box
- Three status LEDs (register/signal, power, relay); licensed electrician required for mains wiring
Hikvision DS-PM1-O4H-H AX Hybrid Pro 4-Way Output Module to suit Hardwired Alarm Controller
The Hikvision DS-PM1-O4H-H is a wired 4-way power output module for AX Hybrid Pro hardwired alarm controllers. It gives the panel four high-current relays that can switch mains-powered devices - sirens, strobes, lighting circuits, gates and shutters - on command over the Speed-X bus, turning an alarm event into real-world action.
At a glance
- Four onboard power relays, each rated to switch up to 16A
- Connects to a 100-240 VAC source and opens/closes circuits on command
- Controlled by the AX Hybrid Pro panel over the Speed-X bus
- Cascade support: 1 uplink and 1 downlink Speed-X port for more expanders
- Front and rear tamper, plastic enclosure, mains wiring by a licensed electrician
Hikvision DS-PM1-O4L-H 4-Way Relay Expander
The Hikvision DS-PM1-O4L-H is a wired four-way relay expander for an AX Hybrid Pro alarm system. Speed-X connections link it to the control panel and support expansion. Each relay can switch a compatible 6 to 30 V circuit at up to 5 A; the separate auxiliary output has a 500 mA maximum.
Hikvision DS-PM1-RT-HWB AX Hybrid Tri-X Wireless Receiver
The Hikvision DS-PM1-RT-HWB is a Tri-X wireless receiver for the AX Hybrid PRO wired alarm platform. Connected to a DS-PHA64 panel over the Speed-X bus, it adds 433 MHz two-way wireless so you can mix Hikvision wireless detectors and sounders into a hardwired system - ideal where running cable to every device is impractical.
Key points
- Adds 433 MHz Tri-X wireless to a wired AX Hybrid PRO (DS-PHA64) panel
- Supports up to 32 wireless detectors
- Supports up to 4 indoor and 8 outdoor wireless sounders
- Connects to the panel over the Speed-X bus
- 433 MHz two-way wireless with 128-bit AES and frequency hopping
- Wired 9-28 VDC power; up to 1300 m open-space range
Hikvision DS-PM2-P PSTN Alarm Communication Module
The Hikvision DS-PM2-P is a PSTN communication module for compatible AX Hybrid Pro control panels. It provides telephone-line alarm communication using Contact ID. A suitable telephone service and alarm receiving arrangement are required.
Hikvision DS-PM2-S(AU) 3G/4G Communication Module(AU)
The Hikvision DS-PM2-S(AU) is a 3G/4G communication module that adds cellular reporting to a Hikvision AX Hybrid Pro alarm panel. With a SIM fitted, the panel can send alarms and notifications over the mobile network - useful where there is no phone line, or as a resilient backup to a wired internet path.
At a glance
- Adds 3G/4G cellular alarm reporting to AX Hybrid Pro hardwired panels
- AU variant: LTE-FDD B1/B3/B5/B7/B8/B28/B66, LTE-TDD B40, WCDMA and GSM
- SIM card slot - a suitable SIM and mobile coverage are required
- Plug-in module design for neat installation inside the panel
- Use as a primary or backup reporting path, -10 to +40 degrees C
Hikvision DS-PM2-S(AU) AX Hybrid Pro Series, Wired 3G/4G Communication Module
The Hikvision DS-PMA is a 3G/4G communication module for Hikvision AX Hybrid Pro hardwired alarm panels. It plugs into the panel and adds a cellular reporting path, so alarms and notifications can be sent over the mobile network - ideal where there is no phone line, or as a backup to a wired internet connection.
At a glance
- Adds 3G/4G cellular reporting to AX Hybrid Pro hardwired panels
- SIM card slot - a suitable SIM and mobile coverage are required
- Plug-in module design for a neat install inside the panel
- Use as a primary or backup reporting path
- Communication accessory only - panel and devices ordered separately
Before you buy
What customers ask most before ordering from this range — and how we deliver.
Which kit is right for me?
Start with three questions: how many areas do you need to cover, do you want colour night vision, and do you want AI alerts that ignore cars and animals? For most homes, a 4-camera 8MP ColorVu or Full-Colour kit is the sweet spot. Not sure? Use our CCTV Advisor — answer a few questions and it recommends a kit — or email us and we'll spec it with you.
Is your Hikvision, Dahua, HiLook and TP-Link VIGI stock genuine Australian stock?
Yes, 100%. Every Hikvision, Dahua, HiLook and TP-Link VIGI product we sell is a genuine Australian-market model sourced through Australian supply chains — never grey imports. That means factory-sealed units, Australian-region firmware that works with the official apps out of the box, and a full 3-year local warranty.
How long does delivery take?
Metro delivery usually takes 2–4 business days after dispatch, and regional areas may take longer. You'll receive a tracking number by email as soon as your order leaves the warehouse.
How much is shipping?
Standard shipping is free on all orders over $300 AUD, Australia-wide. Orders under $300 ship at a flat rate of $25, calculated at checkout. Tracking is included on every order.
What warranty do you offer?
All cameras, NVRs and DVRs come with a 3-year back-to-base manufacturer warranty covering defects in materials and workmanship, in addition to your rights under Australian Consumer Law. Hard drives and accessories are covered as set out in our Warranty Policy.
What is your return policy?
You have 30 days from the day you receive your order to request a change-of-mind return. Items must be unopened, factory-sealed and in resalable condition. A 15% restocking fee applies and return postage is at your cost. Faulty or incorrectly supplied items are different: we cover the return shipping and refund or replace at no charge. Read the full Return & Refund Policy.
Do you offer installation?
We can connect you with licensed installers in Sydney and Melbourne. Installation typically starts from around $200 per camera depending on cable runs and site conditions. Email sales@smarket.com.au with your address and camera count for a quote.
Shop by Brand
Pick your preferred manufacturer ecosystem
Shop by Category
Cameras, recorders, kits and accessories
