Alarm

The Bosch CM710B is a 4-way relay output expansion module for the Bosch Solution 6000 alarm panel. It adds four Form C relay contacts so the system can switch external devices such as a garage door, gate, lights or an electric door strike. Because it runs on the RS485 LAN, it can sit in the panel enclosure or be located out near the device it controls.

Key points
- 4x Form C relay contacts (rated 24VDC at 2A max)
- For the Bosch Solution 6000 / 144; up to 8 CM710B modules per panel
- RS485 LAN powered, 10.5 to 14VDC, 30mA standby
- Co-locate in the panel box or mount remotely (up to 300m of standard cable)
- Status LED, separate tamper input and a service codepad connector
- Supplied as a PCB module; occupies one module space

The Bosch DS9370 is a 360-degree panoramic ceiling-mount motion detector. It uses TriTech sensing (passive infrared plus microwave Doppler radar) to cover large open indoor areas from above, with a 21 m (70 ft) diameter detection pattern and reliable performance at high ceilings.

Key points
- 360-degree panoramic coverage, mounted on the ceiling
- TriTech: passive infrared (PIR) plus microwave Doppler radar, to cut false alarms
- 21 m (70 ft) diameter coverage pattern with fully adjustable optics
- Mounts at ceiling heights up to 7.6 m (25 ft)
- Digital signal processing; hinged chassis and walk-test LED for easy setup
- Wired detector for indoor use; 9-15VDC; -20 to +55 degrees C

The Bosch CC610P is the control panel PCB for the Bosch Solution 6000 alarm and access control system. It is the board (PCB only) at the heart of a Solution 6000, supporting 16 on-board zones expandable to 144 wired or wireless, eight areas and integrated access control for up to 16 doors.

Key points
- Solution 6000 control panel, supplied as the PCB only
- 16 on-board zones, expandable to 144 (wired or wireless)
- Partitionable into 8 areas; up to 990 users (PIN, token, keyfob, fingerprint)
- 5 on-board outputs, expandable to 37; access control for up to 16 doors
- Up to 16 keypads or readers; reporting by CID, SIA, IP, voice and SMS
- 16-18V AC supply; needs a keypad, enclosure, transformer, battery and detectors to make a system

The Bosch PR116B is an external smart-card reader in a white mullion housing for the Bosch Solution 6000 alarm panel. Rated IP66 and made from vandal-resistant ASA plastic, it lets users arm, disarm and control a door by presenting a MiFare card or token at an entry point.

Key points
- External, IP66 weather-resistant, white mullion housing
- MiFare 40-bit smart-card reader (PR301B, PR350B, PR365B tokens)
- Alarm and access control on the Bosch Solution 6000 (also 16i and 144)
- Encrypted RS485 LAN with two-way authentication; occupies one keypad position
- Red, green and blue LEDs for area and door-lock status
- 10 to 14.5VDC, 100mA max; 500mA lock output and egress input

The Bosch RF120 is a Smart 2-way RF base station that adds wireless to a Bosch Solution 6000 panel over an RS485 LAN connection. It is a 433.42MHz transceiver that lets the panel use Bosch RADION wireless sensors and RF110 two-way remote controls.

Key points
- Smart 2-way 433.42MHz RF base station for the Bosch Solution 6000
- Connects to the panel over an RS485 LAN connection
- Supports Bosch RADION wireless sensors and RF110 5-button remotes
- Two transmitters/receivers with dual-diversity internal antennas
- Encrypted 2-way RF with rolling code and anti-substitution
- Front and rear tamper; status LED; 10-14VDC; indoor use

The Bosch RF110 is a 5-button Smart RF keyfob for the Bosch Solution 6000 alarm system. It gives handheld arm and disarm, area control and output triggering, and works with the RF120 Smart RF Base Station receiver, which is sold separately.

Highlights
- 5-button Smart RF keyfob for the Bosch Solution 6000
- Each button supports two functions: a single press and a 2-second hold-down
- Arm and disarm, control areas or part modes, and trigger outputs such as a gate or door
- Requires the Bosch RF120 Smart RF Base Station (sold separately)
- Not compatible with Solution 2000/3000 or with B810/STR receivers

The Bosch ICP-SOL3-P is the control panel board (PCB) for the Solution 3000 alarm system, a flexible 16-zone panel for homes and small commercial sites. It supports a mix of wired and wireless detectors, can be split into two independently armed areas, and works with the Bosch RSC+ app for phone control when an IP or mobile module is fitted. Note that this is the PCB only - to build a working system you add a keypad, enclosure, plug pack, battery and detectors.

Key points
- Solution 3000 control panel board with 16 fully programmable zones
- Wired and wireless detectors (RADION or WE800EV2 receiver)
- Partitionable into two separate areas; STAY/AWAY arming
- 33 codes (1 installer + 32 user) and up to 16 wireless devices
- RSC+ phone app via a B426-M or B450-M communications module
- PCB only: add a keypad, MW250 enclosure, 18VAC plug pack and 12V battery

The Bosch CM704B adds hardwired zones to a Bosch Solution control panel. Each module provides eight physical zone inputs and, depending on the end-of-line wiring, expands the panel by either 8 or 16 zones. It connects over the RS485 keypad LAN, so it can sit inside the panel enclosure or be located remotely near the detectors, and it can be powered from the panel LAN or a local supply. It suits the Solution 16i and Solution 6000 panels.

Key points
- Adds 8 physical zone inputs (8 or 16 zones with end-of-line wiring)
- For Bosch Solution 16i and Solution 6000 panels
- RS485 4-wire LAN - co-locate in the panel or mount remotely
- LAN-powered or locally powered (input current-limited to 1 A)
- Separate tamper input and a service code-pad connection
- Status and zone-power LEDs; dip-switch addressing; 3-year warranty