Products

The Hikvision DS-PKA-WLM-433 is a wireless touch keypad for the Hikvision Axiom wireless alarm hub. Its full touchscreen, LED backlight and built-in IC card reader give users a clean, modern way to arm, disarm and check the system - by code or with a simple card swipe - without running any cabling.

At a glance
- Full touchscreen keypad with LED backlight for the Axiom / wireless AX hub
- Built-in IC card reader for arm and disarm by card swipe, plus patrol card
- 10 numeric and 6 function keys (fire, away/stay arm, disarm, delete, confirm)
- 433MHz two-way wireless, up to 800m open-air range
- 4 x AA batteries up to 3 years, front and rear tamper, indoor

The Hikvision DS-PM1-I1-WB is a wireless input transmitter for AX PRO alarm systems. It bridges one existing wired detector, contact or alarm device into the AX PRO wireless system, so you can reuse proven wired hardware on a modern wireless panel without running new cable back to the hub.

At a glance
- Converts one wired alarm input (PIR, reed, vibration, contact) into a wireless AX PRO zone
- One alarm input, one tamper input, one programmable PGM output, plus a 3.3V output for low-current sensors
- Tri-X two-way wireless on 433MHz (2GFSK), up to 1300m open-air, AES-128
- Three CR123 batteries, up to 5 years; built-in tamper
- Compact module fits inside a wireless-ready detector or beside the wired device

The Hikvision DS-PM1-I16O2-WB is an AX PRO wireless multi-I/O expander that lets you keep existing wired detectors when you move to a Hikvision AX PRO wireless alarm. It connects up to sixteen hardwired inputs and two outputs and reports them back to the wireless hub over Tri-X radio - so legacy cabling and sensors stay in use instead of being replaced.

At a glance
- Integrates up to 16 wired alarm inputs and 2 outputs into an AX PRO wireless system
- Tri-X two-way 433MHz radio to the hub, up to 800m open-air, AES-128 secured
- Each zone independently set to NO/NC, EOL or DEOL for professional wired sensors
- Mains powered 100-240 VAC, takes a 12V 7Ah backup battery for up to 36 hours
- For AX PRO wireless hubs - not for the DS-PHA64 hardwired panel

The Hikvision DS-PM1-I8O2-H is a Speed-X wired input expander for the AX Hybrid Pro alarm panel. It adds eight on-board wired zones and two collector outputs to a hardwired system, so you can connect more detectors, contacts and output devices than the panel alone supports.

At a glance
- Adds 8 wired zones + 2 outputs to an AX Hybrid Pro (DS-PHA64) panel
- Connects over the Speed-X bus, up to 900m of cable, and cascades to further expanders
- 3EOL wiring (1k alarm / 1k tamper / 2.2k fault) with zone, tamper, mask, fault and short detection
- 11-24VDC input; output 9-12VDC up to 500mA to power wired detectors directly
- Front and rear tamper protection; power and fault LED indicators
- Wired expansion module - not for the wireless AX PRO (PWA96) hub

The Hikvision DS-PM1-O1H-WB is a wireless wall switch for AX PRO alarm systems, with a high-power relay that switches mains circuits directly. Linked to your alarm by 433MHz two-way wireless, it can turn lighting or appliances on and off on an alarm, a schedule or a manual command - no control cable back to the hub.

At a glance
- Single relay output, NO/NC, 100-240V AC up to 13A - switches mains loads directly
- 433MHz two-way wireless (2GFSK) to the AX PRO hub, up to 800m, AES-128 encrypted
- Scenario control: by alarm, by operation, by fault, by schedule or manual
- Mains powered (100-240V AC, 50/60Hz); wall mount or inside a standard 86 box
- Three status LEDs (register/signal, power, relay); licensed electrician required for mains wiring

The Hikvision DS-PM1-O4H-H is a wired 4-way power output module for AX Hybrid Pro hardwired alarm controllers. It gives the panel four high-current relays that can switch mains-powered devices - sirens, strobes, lighting circuits, gates and shutters - on command over the Speed-X bus, turning an alarm event into real-world action.

At a glance
- Four onboard power relays, each rated to switch up to 16A
- Connects to a 100-240 VAC source and opens/closes circuits on command
- Controlled by the AX Hybrid Pro panel over the Speed-X bus
- Cascade support: 1 uplink and 1 downlink Speed-X port for more expanders
- Front and rear tamper, plastic enclosure, mains wiring by a licensed electrician

The Hikvision DS-PM1-RT-HWB is a Tri-X wireless receiver for the AX Hybrid PRO wired alarm platform. Connected to a DS-PHA64 panel over the Speed-X bus, it adds 433 MHz two-way wireless so you can mix Hikvision wireless detectors and sounders into a hardwired system - ideal where running cable to every device is impractical.

Key points
- Adds 433 MHz Tri-X wireless to a wired AX Hybrid PRO (DS-PHA64) panel
- Supports up to 32 wireless detectors
- Supports up to 4 indoor and 8 outdoor wireless sounders
- Connects to the panel over the Speed-X bus
- 433 MHz two-way wireless with 128-bit AES and frequency hopping
- Wired 9-28 VDC power; up to 1300 m open-space range

The Hikvision DS-PM2-S(AU) is a 3G/4G communication module that adds cellular reporting to a Hikvision AX Hybrid Pro alarm panel. With a SIM fitted, the panel can send alarms and notifications over the mobile network - useful where there is no phone line, or as a resilient backup to a wired internet path.

At a glance
- Adds 3G/4G cellular alarm reporting to AX Hybrid Pro hardwired panels
- AU variant: LTE-FDD B1/B3/B5/B7/B8/B28/B66, LTE-TDD B40, WCDMA and GSM
- SIM card slot - a suitable SIM and mobile coverage are required
- Plug-in module design for neat installation inside the panel
- Use as a primary or backup reporting path, -10 to +40 degrees C